Serious Skincare’s Facial Tone & Lift System includes the Facial Toning Tool, Reverse Lift Facial Toning Gel, Reverse Lift Firming Cleanser and Reverse Lift Firming Pads. The Facial Toning Tool tones and firms the muscles in the face through adjustable, modulating, electronic impulses. This FDA approved device lifts, firms and tones the look of sagging, loose skin. Upper eyelids can look lifted and more open. Cheekbones look higher and cheeks look fuller. The jawline appears firmed and tightened and the double chin looks toned. Increases of circulation bring vibrancy back to the complexion and the skin feels more awake and alive. Our unique design allows simultaneous treatment on both sides of your face to occur at one time – this cuts your regimen time in half a maximum of 15 minutes a day, 3-4 times a week promises amazing results.

 

P r o d u c t Fe a t u r e s

2 Hand Held Units with Contact Nodules

3 Programs: - Program 1: Deep Toning

                   - Program 2: Surface Toning

                   - Program 3: Enhancing Routine

Conductive Gel

Reverse Lift Cleanser

Reverse Lift Firming Pads

LCD Display indicates program selected, elapsed time and intensity level

9 Volt Battery

White Cosmetic Bag

Q: Can I use it more than once a day?

A: We recommend no more than one treatment a day.


Q: Do I keep the probes in one place or do I slowly slide them up?

A: Either way... or both. Keeping the probes in one place provides a deeper, more intense muscle contraction- This is good for toning and re-sculpting the face. Sliding the probes during the pulsation helps improve circulation, revitalizes skin tone and provides a overall lifting effect.

Q: IS THE CONDUCTIVE GEL NECESSARY AND IF SO, HOW MUCH?
A: Yes the Conductive Gel is necessary. The skin must be wet in order for the Tool to work. Be sure to have a layer of Conductive Gel on the skin at all times. If the gel dries on the skin during your treatment simply remoisten by applying more gel to the face and/or directly to the individual probes.

Q: THE MACHINE SEEMS TO BE WORKING- IT TURNS ON, BEEPS ECT... BUT I DON'T FEEL ANYTHING ON MY FACE.

A #1: INTENSITY LEVEL: The Facial Toning Tool features 10 intensity levels- each time you turn the Tool 'ON' it starts at LEVEL 0. The green 'Intensity' Up Arrow button (on the outside of the tool) must be pressed several times to reach a level that can be felt on your skin. The Tool will not start until you choose your Intensity. The Intensity buttons are conveniently located on the outside of the Tool to allow you to adjust the level of intensity, lower or higher, to each area of the face you are treating without taking the probes off of the face.

A #2: CONDUCTIVE GEL: The face must be wet. Make sure there is a layer of Conductive Gel on the skin, on the area you are treating.

Q: WHY DOES THE MACHINE TURN OFF AFTER 1 MINUTE?

A: After each 1 minute interval the machine stops and beeps, indicating that it is time to move to the next treatment spot of the face. Simply tap the Intensity Button once on the outside of the tool to initiate another 1 minute interval as you slide the tool to the next treatment spot. This should not even require you to remove the probes from the skin. By tapping the green Intensity UP arrow button once, the Tool will continue at the exact same level as you were just using- from here you can now adjust up or down.

Q: WHAT AM I SUPPOSED TO FEEL?

A: The Facial Toning Tool does not warm, vibrate or massage. It sends alternating impulses into the skin to contract and then release the muscle. You should feel a small current tensing the facial muscle and then relaxing it in 5 second intervals ie tense for 5 seconds, relax for 5 seconds, tense for 5 seconds etc... . The feeling should be comfortable, if the impulse is too strong or feels like a 'bite' to the skin- lower the intensity by pressing the red down-arrow Intensity button found on the outside of the tool.

Q: I FEEL A CURRENT COMING FROM ONE OF THE TOOLS BUT NOT THE OTHER. SHOULDN'T BOTH SIDES OF THE TOOL WORK THE SAME?

A: Yes, both sides of the Tool should work the same when treating both sides of the face at once. Make sure both sides of the face being treated have the same amount of Conductive Gel. Also, adjust the position of the probes slightly for each side of the face until you feel the impulse connect. Our faces are not perfectly symmetrical and the positions on the face may need to be found individually from side to side.